50mm Square x 12-inch Angled Mechanical Anchor Plate

Part No: ANCHORPLATE-12M-50S-Angled Category: Tag:
Part No: ANCHORPLATE-12M-50S-Angled Category: Tag:

Price

$24.50 Inc.GST

Shipping

Select delivery location

Couplemate accepts PayPal, Visa and Mastercard.

50mm Square x 12-inch Angled Mechanical Caliper Anchor Plate

A 50mm square x 12-inch angled mechanical Caliper Anchor Plate attaches the brake calipers to the axle on 12-inch mechanical disc rotors.

The mechanical caliper anchor plate is 10mm thick and 90mm between holes for Australian calipers.

The threaded hole size is 7/16″ UNF. However, depending on the brand of caliper used, the bolt’s length can vary from 50mm to 56mm.

Couplemate suggests all anchor plates are dry fitted and tacked welded before the welding process is finished.

In most cases, failure to dry-fit every anchor plate will result in wrong fits.

How to dry-fit anchor plates?

  • Insert bearings into the rotor with no grease and fit the rotor to the axle. (tighten)
  • Assemble the caliper onto the mount bracket and tighten it.
  • Align the caliper over the rotor and tighten the pad adjustment bolt. (Note: Place a zip tie or Q strap between the rotor and caliper to prevent the caliper from touching the rotor when it is spinning.)
  • Align the caliper on the slides by sliding the caliper backwards so that approx 5mm of the slide is showing on the inside of the caliper. The caliper will slide backwards when the pads wear.
  • Carefully tack the mounting plate.
  • Disassemble the entire setup except for the mount plates.
  • Tape the bearing journals.
  • Carefully weld the small flat section of the mounting plate on the sides, then weld the main area farthest away from the bearing journal. (note: Weld one side of the mounting plate is sufficient)
  • Repeat on the other end.

Grease bearings with high-temperature grease and assemble rotors. Tighten the adjustment bolt until tight, then back off 1/2 turn and lock the thread with the lock nut.

Note: Grind galvanising on your axle back to bare metal before welding. After welding, apply a spray pack of cold gal while the mount plates are still hot.

Notably, the mechanical caliper anchor plate should be installed at an angle that clears the trailer or caravan springs.

Finally, if this mechanical anchor plate is not the product you wish to buy, review the list of more anchor plates below.

Additional information

Weight1 kg
Dimensions10 × 10 × 1 cm
Stud Thread

7/16" UNF – 490200

Our Service Lifetime Warranty

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Couplemate™ is a manufacturer and vendor of high-quality towing, trailer, and caravan components. Couplemate™ Core Goods and Custom Work are guaranteed to be free of defects for the service lifetime of the product when used as intended.

Warranties are non-transferrable and Couplemate™ requires satisfactory proof of purchase prior to issuing a remedy. The full Couplemate™ Warranty Policy can be found in the Terms & Conditions: Section 8 – Consumer Guarantees & Warranty.

Warranties are in addition to your rights under the Australian Consumer Law. If something is wrong with your order, please contact our team.

60-Day Returns

After 60 years of experience, we know that life has its unpredictable moments.

All Couplemate™ orders (online, over the phone, or in-store) have a 60 day period for change-of-mind returns and exchanges. There are some items that can’t be returned and some returns may incur a 15% restocking fee.

You can view our full policy for change-of-mind returns here.

Reviews

    Be the first to review “50mm Square x 12-inch Angled Mechanical Anchor Plate”

    Your email address will not be published. Required fields are marked *

    High-Quality Trailer Parts

    Couplemate™ Core Range

    Couplemate Trailer Parts.

    About Us

    Contact Info

    Trade & Wholesale

    Australian Made

    Australian Made

    FAQ