Hydraulic Caliper Anchor Plate

Part No: N/A Category: Tag:
Part No: N/A Category: Tag:

$21.55$52.84

Shipping

Select delivery location

Couplemate accepts PayPal, Visa and Mastercard.

Hydraulic Caliper Anchor Plate

Hydraulic Caliper Anchor Plate suit hydraulic calipers on all Al-ko 10-inch and 12-inch disc rotors.

Anchor plates are 10mm thick and 90mm between holes for Australian brake calipers.

7/16 inch UNF is the hole size.

Caliper Anchor Plates to suit

  • 39mm Round 10 inch
  • 40mm Square 10 inch
  • 45mm Round 10-inch and 12 inch
  • 45mm Square 10-inch and 12 inch
  • 50mm Square 10-inch and 12 inch
  • 60mm Round 12 inch

Couplemate suggests all anchor plates are dry fitted and tacked welded before the welding process is finished. In most cases, failure to dry-fit every anchor plate will result in wrong fits.

How to dry-fit anchor plates?

  1. Insert bearings into the rotor with no grease and fit the rotor to the axle. (tighten)
  2. Assemble the caliper onto the Hydraulic Caliper Anchor Plate and tighten it.
  3. Align the caliper over the rotor and tighten the pad adjustment bolt. (note: place a zip tie or Q strap between the rotor and caliper to stop the caliper from touching the rotor when it is spinning.)
  4. Align the caliper on the slides by sliding the caliper backwards so that a gap of approximately 1mm or more exists on either side of the arms holding the pads into position. The caliper will slide back when the pads wear.
  5. Carefully tack the mounting plateDisassemblele the entire setup except for the mount plates.
  6. Tape the bearing journals.
  7. Carefully weld the small flat section of the mounting plate on the sides, then weld the central part farthest away from the bearing journal. (note: Weld one side of the mounting plate is sufficient)
  8. Repeat on the other end.
  9. When testing,g ensure the discs brake quickly and evenly. Air bubbles in the hydraulic line will significantly diminish the effects of braking.

Grease bearings with high-temperature grease and assemble rotors. Tighten the adjustment bolt until tig,ht, then back off 1/2 turn and lock the thread with the lock nut.

Note: Grind galvanising on your axle back to bare metal before welding. After welding, apply a spray pack of cold gal while the mount plates are still hot.

These anchor plates fit this type of caliper only. Click here.

Importantly, anchor plates should be installed at an angle that clears the trailer or caravan springs.

Learn why Bearing Buddy’s fall-off wheel hubs.

Finally, hydraulic anchor plates do not fit mechanical calipers anvicesa versa.

The links below contain hydraulic caliper spare parts

Additional information

Weight1 kg
Dimensions10 × 10 × 1 cm
Hydraulic Anchor Plates

39mm Round suit 10-inch Disc Rotors, 40mm Square suit 10-inch Disc Rotors, 45mm Round suit 10-inch Disc Rotors, 45mm Round suit 12-inch Disc Rotors, 45mm Square suit 10-inch Disc Rotors, 45mm Square suit 12-inch Disc Rotors, 50mm Square suit 10-inch Disc Rotors, 50mm Square suit 12-inch Disc Rotors – Straight, 50mm Square suit 12-inch Disc Rotors – Angled, 60mm Round suit 12-inch Disc Rotors

Our Service Lifetime Warranty

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Couplemate™ is a manufacturer and vendor of high-quality towing, trailer, and caravan components. Couplemate™ Core Goods and Custom Work are guaranteed to be free of defects for the service lifetime of the product when used as intended.

Warranties are non-transferrable and Couplemate™ requires satisfactory proof of purchase prior to issuing a remedy. The full Couplemate™ Warranty Policy can be found in the Terms & Conditions: Section 8 – Consumer Guarantees & Warranty.

Warranties are in addition to your rights under the Australian Consumer Law. If something is wrong with your order, please contact our team.

60-Day Returns

After 60 years of experience, we know that life has its unpredictable moments.

All Couplemate™ orders (online, over the phone, or in-store) have a 60 day period for change-of-mind returns and exchanges. There are some items that can’t be returned and some returns may incur a 15% restocking fee.

You can view our full policy for change-of-mind returns here.

Reviews

    Be the first to review “Hydraulic Caliper Anchor Plate”

    Your email address will not be published. Required fields are marked *

    Custom ICS Quote

    Couplemate™ Off-Road Independent Coil Suspension.
    couplemate trailer parts australian made

    Australian Made

    We supply Australian Made trailer and caravan parts.

    Installation Help

    Check out our FAQs and installation guides.

    High-Quality Trailer Parts

    Couplemate™ Core Range

    Couplemate Trailer Parts.

    About Us

    Contact Info

    Trade & Wholesale

    Australian Made

    Australian Made

    FAQ